Instrument Rentals
The 12 Volt Battery Pack Rental provides you with mobility in the field.
Enviro-Equipment offers 12 Volt Deep Cycle Marine Battery Rentals for use with groundwater sampling pumps. These batteries are commonly used when a vehicle is not able to access the sampling area at the site.
NOTE: This item is not available for shipping! The order must be for local courier or pickup at our office.
**NOTE: Calibration Kit Rentals are only available for PICKUP, gas must be purchased if the items need to be shipped.**
All of our gas monitor rentals are calibrated before they are sent to you. However, sometimes you are required to do your own calibrations in the field.
The 4-Gas / PID Calibration Kit Rental is used to perform field calibrations on the 4-Gas meters with PIDs.
Includes:
- Cal Gas: 10 ppm hydrogen sulfide (H2S), 50 ppm carbon monoxide (CO), 50% LEL methane (2.5% CH4), 18% oxygen (O2)
- Cal Gas: 100 ppm isobutylene (C4H8)
- Calibration Gas Regulator
**NOTE: Calibration Kit Rentals are only available for PICKUP, gas must be purchased if the items need to be shipped.**
All of our gas monitor rentals are calibrated before they are sent to you. However, sometimes you are required to do your own calibrations in the field.
The 4-Gas Calibration Kit Rental is used to perform field calibrations on Multi-Gas Detection Monitors.
Includes:
- Cal Gas: 10 ppm hydrogen sulfide (H2S), 50 ppm carbon monoxide (CO), 50% LEL methane (2.5% CH4), 18% oxygen (O2)
- Calibration Gas Regulator
- Ground penetration using manual cross handle or slide hammer.
- Hardened stainless alloy tip with vent holes for gas entry.
- [2] 3' Hollow extensions included.
- Sample with reusable retractable tip or dedicated stainless steel sampling tip (purchased separately).
- Ground penetration by slide hammer or electric rotary drive hammer.
- [4] 3' GVP 5/8" extensions allow sampling up to 12 feet depth.
- Fluoropolymer tubing (purchased separately) is attached to a barb fitting on the GVP tip for remote sampling from the surface.
*Only available for PICK-UP (Charlotte, NC) orders*
- Collects soil core in 2" x 6" stainless steel liner.
- Drive into ground using slide hammer or cross handle.
- [3] 5' extensions to sample at a max depth of 15 feet.
- 7/8" x 33" sample probe with 13" window.
- Drive probe using cross handle or slide hammer.
- Includes up to [3] 5' rod extensions.
- Includes auto-level standard equipment with tri-pod and survey rod (11 or 25ft).
- Brands available include Sokkia and Topcon
*Only available for PICK-UP (Charlotte, NC) orders*
- 1/30 HP motor, 12V DC Power (3 amps)
- Max flow: 0.64 CFM (18 L/min)
- Max vacuum: 18" Hg
- Max pressure: 15 PSIG
The Bosch VAC090AH 9-Gallon Dust Extractor with Auto Filter Clean and HEPA Filter provides a complete package that is designed to help users move toward compliance with the OSHA silica dust regulation.
- Operation Modes: rotary hammer and hammer-only.
- 9.6 feet-pound of impact energy
- Tool-free bit changes
- Flow range: 0.8 to 5 L/min; 5 to 850 mL/min with low flow adaptor.
- Datalogging capability: start/stop time, flow rate, volume sampled, temperature
- Battery life: 10-40 hours depending upon pressure load.
- Type 2 Sound Level Meter for general noise measurements.
- Datalogging Capability: 100 separate run capacity with up to 65,000 samples for each run (1, 2, 5 or 10 second intervals).
- Measurement Ranges: 30-100 dB and 60-130 dB.
- "A" and "C" Frequency Weightings; Slow, Fast, and Impulse Time Weightings.
- Field calibrator and annual factory calibration certificate included.
- Displayed parameters: Instantaneous level (Lp), Maximum level (Lmx) and Time Average Level (Leq or Lavg).
- Clips onto workers to gather personal noise dosage data for OSHA or ISO compliance.
- Measurement Range: 65-140 dB.
- 3 and 5 dB exchange rates, time average, C and Z peak levels, calculates % noise dose plus Lavg and TWA.
- Software included for data download and generating reports and graphs.
- Field calibrator and annual factory calibration certificate included.
- Type 1 ANSI Sound Level Meter, 20-140 dB measurement range.
- Octave (16 Hz to 16 kHz) and 1/3 octave (12.5 Hz to 20 kHz) band measurements for Lmx and Leq with selected frequency and time weightings.
- Broadband measurement in periodic or cumulative mode for summary data, profile mode for individual noise captures at user defined interval.
- Software included for data download and generating reports and graphs.
- Field calibrator and annual factory calibration certificate included.
- Extensive range: 0.001 mg/m3 to 250 g/m3 (auto-ranging)
- Real-time graphical display of dust levels
- Simple icon driven user interface
- Unique removable sampling probe
- Rugged design for harsh environments
- Sample for total, respirable, PM2.5, or PM10 with optional adapter
- Unique on-site calibration insert
- Instrinsically Safe
- Bluetooth® Connectivity
- Measures all noise dose parameters simultaneously
- Long battery life
- Compliant with ANSI S1.25 - 1991 (R2007)
- Measures total dust from 0-2500 mg/m3, auto ranging between 0-2.5, 0-25, 0-250, and 0-2500 mg/m3.
- 0.001 mg/m3 (1ug/m3) resolution.
- Respirable, PM2.5 and PM10 capable (accessories required).
- Software for data download included.
- Field calibrator and annual factory calibration certificate included.